Search Results

Load data for .308 | 165gr | Swift A-Frame bullet in caliber .300 Weath. Mag. and 142 powders such as Alliant Reloder-23, Alliant Reloder-26, Ramshot Hunter, Vihtavuori N555, Winchester StaBALL HD, etc. Load data for .300 Weath. Mag. + .308 | 165gr | Swift A-Frame Recommended Powder(s): Alliant Reloder-23, Alliant Reloder-26, Ramshot Hunter, Vihtavuori N555, Winchester StaBALL HD Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .308 | 165gr | Swift A-Frame Bullet Weight: 165gr | 10.7g Bullet Diameter: 0.308" | 7.82mm Bullet Length: 1.140" | 29.0mm Caliber: .300 Weath. Mag. load data Case Length (l3): 2.824" | 71.7mm Cartridge Length (C.O.L.): 3.507" | 89.1mm Seated Depth: 0.457" | 11.6mm Shank Seated Depth: 0.457" | 11.6mm Case Capacity: 98.9 Grains of Water | 6.42 cm³ Primer Size: Large Rifle Magnum (LRM) Max. allowed Pressure: 63817 psi | 4400 bar LID: LID_B10844_C379 Last updated: 2025-02-02 Load data for 0 loads in caliber .300 Weath. Mag. with .308 | 165gr | Swift A-Frame bullet and 0 powders such as Alliant Reloder-23, Alliant Reloder-26, Ramshot Hunter, Vihtavuori N555, Winchester StaBALL HD. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .284 | 140gr | Woodleigh HS bullet in caliber 7 mm Blaser Mag and 136 powders such as , etc. Load data for 7 mm Blaser Mag + .284 | 140gr | Woodleigh HS Recommended Powder(s): Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .284 | 140gr | Woodleigh HS Manufacturer SKU: H7mm Bullet Weight: 140gr | 9.1g Bullet Diameter: 0.284" | 7.21mm Bullet Length: 1.170" | 29.7mm Caliber: 7 mm Blaser Mag load data Case Length (l3): 2.303" | 58.5mm Cartridge Length (C.O.L.): 3.250" | 82.6mm Seated Depth: 0.223" | 5.7mm Shank Seated Depth: 0.223" | 5.7mm Case Capacity: 82.5 Grains of Water | 5.36 cm³ Primer Size: Large Rifle Magnum (LRM) Max. allowed Pressure: 60916 psi | 4200 bar LID: LID_B12043_C1050 Last updated: 2026-01-20 Load data for 0 loads in caliber 7 mm Blaser Mag with .284 | 140gr | Woodleigh HS bullet and 0 powder(s). The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .284 | 145gr | Speer Boat Tail Soft Point bullet in caliber 7 x 57 R and 118 powders such as Alliant Reloder-17, Ramshot Big Game, ReloadSwiss RS 60, Somchem S365, Winchester 6.5 StaBALL, etc. Load data for 7 x 57 R + .284 | 145gr | Speer Boat Tail Soft Point Recommended Powder(s): Alliant Reloder-17, Ramshot Big Game, ReloadSwiss RS 60, Somchem S365, Winchester 6.5 StaBALL Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .284 | 145gr | Speer Boat Tail Soft Point Manufacturer SKU: 1628 Bullet Weight: 145gr | 9.4g Bullet Diameter: 0.284" | 7.21mm Bullet Length: 1.165" | 29.6mm Caliber: 7 x 57 R load data Case Length (l3): 2.244" | 57.0mm Cartridge Length (C.O.L.): 3.025" | 76.8mm Seated Depth: 0.384" | 9.8mm Shank Seated Depth: 0.234" | 5.9mm Case Capacity: 60.0 Grains of Water | 3.90 cm³ Primer Size: Large Rifle (LR) Max. allowed Pressure: 49313 psi | 3400 bar LID: LID_B6124_C1089 Last updated: 2025-01-01 Recommended Twist Rate: 1:12 - 1:10 Load data for 0 loads in caliber 7 x 57 R with .284 | 145gr | Speer Boat Tail Soft Point bullet and 0 powders such as Alliant Reloder-17, Ramshot Big Game, ReloadSwiss RS 60, Somchem S365, Winchester 6.5 StaBALL. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity Muzzle velocity vs. barrel length Every 1 inch additional barrel length increases muzzle velocity by approx. 29.9 fps Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .311 | 180gr | Prvi Partizan SP BT bullet in caliber 7.62 x 54 R Russian Nagant and 164 powders such as Alliant Reloder-17, Hodgdon CFE223, Ramshot Big Game, ReloadSwiss RS 60, SNPE Vectan SP 11, etc. Load data for 7.62 x 54 R Russian Nagant + .311 | 180gr | Prvi Partizan SP BT Recommended Powder(s): Alliant Reloder-17, Hodgdon CFE223, Ramshot Big Game, ReloadSwiss RS 60, SNPE Vectan SP 11 Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .311 | 180gr | Prvi Partizan SP BT Manufacturer SKU: B-125 Bullet Weight: 180gr | 11.7g Bullet Diameter: 0.311" | 7.90mm Bullet Length: 1.161" | 29.5mm Caliber: 7.62 x 54 R Russian Nagant load data Case Length (l3): 2.114" | 53.7mm Cartridge Length (C.O.L.): 2.994" | 76.1mm Seated Depth: 0.281" | 7.1mm Shank Seated Depth: 0.281" | 7.1mm Case Capacity: 64.0 Grains of Water | 4.16 cm³ Primer Size: Large Rifle (LR) Max. allowed Pressure: 56565 psi | 3900 bar LID: LID_B9161_C1125 Last updated: 2025-01-01 Load data for 0 loads in caliber 7.62 x 54 R Russian Nagant with .311 | 180gr | Prvi Partizan SP BT bullet and 0 powders such as Alliant Reloder-17, Hodgdon CFE223, Ramshot Big Game, ReloadSwiss RS 60, SNPE Vectan SP 11. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity Muzzle velocity vs. barrel length Every 1 inch additional barrel length increases muzzle velocity by approx. 27.1 fps Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .338 | 250gr | A-Square LionLoad bullet in caliber 8.5 x 68 Fanzoj and 158 powders such as Alliant Reloder-26, Hodgdon Superperformance, IMR 4831, Norma 204, Ramshot Hunter, etc. Load data for 8.5 x 68 Fanzoj + .338 | 250gr | A-Square LionLoad Recommended Powder(s): Alliant Reloder-26, Hodgdon Superperformance, IMR 4831, Norma 204, Ramshot Hunter Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .338 | 250gr | A-Square LionLoad Bullet Weight: 250gr | 16.2g Bullet Diameter: 0.338" | 8.59mm Bullet Length: 1.000" | 25.4mm Caliber: 8.5 x 68 Fanzoj load data Case Length (l3): 2.650" | 67.3mm Cartridge Length (C.O.L.): 3.379" | 85.8mm Seated Depth: 0.271" | 6.9mm Shank Seated Depth: 0.271" | 6.9mm Case Capacity: 92.0 Grains of Water | 5.97 cm³ Primer Size: Large Rifle Magnum (LRM) Max. allowed Pressure: 63817 psi | 4400 bar LID: LID_B383_C1209 Last updated: 2025-01-01 Load data for 0 loads in caliber 8.5 x 68 Fanzoj with .338 | 250gr | A-Square LionLoad bullet and 0 powders such as Alliant Reloder-26, Hodgdon Superperformance, IMR 4831, Norma 204, Ramshot Hunter. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .264 | 130gr | Swift Scirocco bullet in caliber 6.5 x 52 R K&S and 120 powders such as Alliant Reloder- TS 15.5, ReloadSwiss RS 52, ReloadSwiss RS 60, Rottweil R 903, Somchem S365, etc. Load data for 6.5 x 52 R K&S + .264 | 130gr | Swift Scirocco Recommended Powder(s): Alliant Reloder- TS 15.5, ReloadSwiss RS 52, ReloadSwiss RS 60, Rottweil R 903, Somchem S365 Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .264 | 130gr | Swift Scirocco Bullet Weight: 130gr | 8.4g Bullet Diameter: 0.264" | 6.71mm Bullet Length: 1.350" | 34.3mm Caliber: 6.5 x 52 R K&S load data Case Length (l3): 2.020" | 51.3mm Cartridge Length (C.O.L.): 2.758" | 70.1mm Seated Depth: 0.612" | 15.5mm Shank Seated Depth: 0.533" | 13.5mm Case Capacity: 47.0 Grains of Water | 3.05 cm³ Primer Size: Large Rifle (LR) Max. allowed Pressure: 47137 psi | 3250 bar LID: LID_B10833_C1009 Last updated: 2025-02-02 Recommended Twist Rate: 1:9 - 1:7 Load data for 0 loads in caliber 6.5 x 52 R K&S with .264 | 130gr | Swift Scirocco bullet and 0 powders such as Alliant Reloder- TS 15.5, ReloadSwiss RS 52, ReloadSwiss RS 60, Rottweil R 903, Somchem S365. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .264 | 123gr | Hornady A-MAX bullet in caliber 6.5 x 54 Mannlich Schoenauer and 146 powders such as Alliant Reloder- TS 15.5, Alliant Reloder-17, ReloadSwiss RS 60, SNPE Vectan SP 11, Somchem S355, etc. Load data for 6.5 x 54 Mannlich Schoenauer + .264 | 123gr | Hornady A-MAX Recommended Powder(s): Alliant Reloder- TS 15.5, Alliant Reloder-17, ReloadSwiss RS 60, SNPE Vectan SP 11, Somchem S355 Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .264 | 123gr | Hornady A-MAX Manufacturer SKU: 26171 Bullet Weight: 123gr | 8.0g Bullet Diameter: 0.264" | 6.71mm Bullet Length: 1.220" | 31.0mm Caliber: 6.5 x 54 Mannlich Schoenauer load data Case Length (l3): 2.112" | 53.6mm Cartridge Length (C.O.L.): 3.017" | 76.6mm Seated Depth: 0.315" | 8.0mm Shank Seated Depth: 0.215" | 5.5mm Case Capacity: 50.0 Grains of Water | 3.25 cm³ Primer Size: Large Rifle (LR) Max. allowed Pressure: 52939 psi | 3650 bar LID: LID_B2581_C1012 Last updated: 2025-09-11 Recommended Twist Rate: 1:10 - 1:8 Load data for 0 loads in caliber 6.5 x 54 Mannlich Schoenauer with .264 | 123gr | Hornady A-MAX bullet and 0 powders such as Alliant Reloder- TS 15.5, Alliant Reloder-17, ReloadSwiss RS 60, SNPE Vectan SP 11, Somchem S355. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .310 | 85gr | Sellier & Bellot FMJ bullet in caliber 7.63 Mauser and 108 powders such as Hodgdon HS-6, etc. Load data for 7.63 Mauser + .310 | 85gr | Sellier & Bellot FMJ Recommended Powder(s): Hodgdon HS-6 Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .310 | 85gr | Sellier & Bellot FMJ Manufacturer SKU: 31962 Bullet Weight: 85gr | 5.5g Bullet Diameter: 0.310" | 7.87mm Bullet Length: 0.551" | 14.0mm Caliber: 7.63 Mauser load data Case Length (l3): 0.990" | 25.1mm Cartridge Length (C.O.L.): 1.359" | 34.5mm Seated Depth: 0.182" | 4.6mm Shank Seated Depth: 0.182" | 4.6mm Case Capacity: 17.2 Grains of Water | 1.12 cm³ Primer Size: Small Pistol (SP) Max. allowed Pressure: 37710 psi | 2600 bar LID: LID_B7231_C1127 Last updated: Mon Jul 14 2025 12:33:56 GMT+0000 (Coordinated Universal Time) Load data for 0 loads in caliber 7.63 Mauser with .310 | 85gr | Sellier & Bellot FMJ bullet and 0 powders such as Hodgdon HS-6. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 5.50'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 5.50'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .308 | 150gr | Sierra HP VARMINTER bullet in caliber 7.5 x 54 mm MAS and 174 powders such as Accurate 4064, Lovex D073.6, Lovex S062, Shooters World Match Rifle, Vihtavuori N540, etc. Load data for 7.5 x 54 mm MAS + .308 | 150gr | Sierra HP VARMINTER Recommended Powder(s): Accurate 4064, Lovex D073.6, Lovex S062, Shooters World Match Rifle, Vihtavuori N540 Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .308 | 150gr | Sierra HP VARMINTER Manufacturer SKU: 2136 Bullet Weight: 150gr | 9.7g Bullet Diameter: 0.308" | 7.82mm Bullet Length: 0.895" | 22.7mm Caliber: 7.5 x 54 mm MAS load data Case Length (l3): 2.120" | 53.8mm Cartridge Length (C.O.L.): 3.014" | 76.6mm Seated Depth: 0.001" | 0.0mm Shank Seated Depth: 0.001" | 0.0mm Case Capacity: 58.0 Grains of Water | 3.77 cm³ Primer Size: Large Rifle (LR) Max. allowed Pressure: 55114 psi | 3800 bar LID: LID_B5501_C1111 Last updated: 2025-12-09 Load data for 0 loads in caliber 7.5 x 54 mm MAS with .308 | 150gr | Sierra HP VARMINTER bullet and 0 powders such as Accurate 4064, Lovex D073.6, Lovex S062, Shooters World Match Rifle, Vihtavuori N540. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .338 | 210gr | Barnes X BT bullet in caliber .338 Lapua Mag. and 118 powders such as ADI AR 2209, Alliant Reloder-19, Alliant Reloder-25, Norma MRP, Rottweil R 905, etc. Load data for .338 Lapua Mag. + .338 | 210gr | Barnes X BT Recommended Powder(s): ADI AR 2209, Alliant Reloder-19, Alliant Reloder-25, Norma MRP, Rottweil R 905 Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .338 | 210gr | Barnes X BT Manufacturer SKU: 33883 Bullet Weight: 210gr | 13.6g Bullet Diameter: 0.338" | 8.59mm Bullet Length: 1.353" | 34.4mm Caliber: .338 Lapua Mag. load data Case Length (l3): 2.724" | 69.2mm Cartridge Length (C.O.L.): 3.626" | 92.1mm Seated Depth: 0.451" | 11.5mm Shank Seated Depth: 0.326" | 8.3mm Case Capacity: 114.0 Grains of Water | 7.40 cm³ Primer Size: Large Rifle Magnum (LRM) Max. allowed Pressure: 60916 psi | 4200 bar LID: LID_B668_C454 Last updated: 2025-01-01 Recommended Twist Rate: 1:14 - 1:12 Load data for 0 loads in caliber .338 Lapua Mag. with .338 | 210gr | Barnes X BT bullet and 0 powders such as ADI AR 2209, Alliant Reloder-19, Alliant Reloder-25, Norma MRP, Rottweil R 905. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .308 | 150gr | CutEdge ER Raptor bullet in caliber .30 Nosler and 174 powders such as Alliant Reloder-16, Hodgdon H414, ReloadSwiss RS 62, ReloadSwiss RS 70, Winchester 760, etc. Load data for .30 Nosler + .308 | 150gr | CutEdge ER Raptor Recommended Powder(s): Alliant Reloder-16, Hodgdon H414, ReloadSwiss RS 62, ReloadSwiss RS 70, Winchester 760 Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .308 | 150gr | CutEdge ER Raptor Manufacturer SKU: ER C150 CU RAPTOR Bullet Weight: 150gr | 9.7g Bullet Diameter: 0.308" | 7.82mm Bullet Length: 1.460" | 37.1mm Caliber: .30 Nosler load data Case Length (l3): 2.550" | 64.8mm Cartridge Length (C.O.L.): 3.290" | 83.6mm Seated Depth: 0.720" | 18.3mm Shank Seated Depth: 0.506" | 12.9mm Case Capacity: 99.0 Grains of Water | 6.43 cm³ Primer Size: Large Rifle Magnum (LRM) Max. allowed Pressure: 64977 psi | 4480 bar LID: LID_B8477_C310 Last updated: 2025-01-01 Recommended Twist Rate: 1:10 - 1:8 Load data for 0 loads in caliber .30 Nosler with .308 | 150gr | CutEdge ER Raptor bullet and 0 powders such as Alliant Reloder-16, Hodgdon H414, ReloadSwiss RS 62, ReloadSwiss RS 70, Winchester 760. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity Muzzle velocity vs. barrel length Every 1 inch additional barrel length increases muzzle velocity by approx. 35.7 fps Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 23.60'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 23.60'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data

Load data for .284 | 140gr | Berger VLD Hunting bullet in caliber 7 x 49 GJW and 98 powders such as Accurate 4100, Hodgdon LilGun, SNPE Vectan BA6 1/2, Vihtavuori N110, etc. Load data for 7 x 49 GJW + .284 | 140gr | Berger VLD Hunting Recommended Powder(s): Accurate 4100, Hodgdon LilGun, SNPE Vectan BA6 1/2, Vihtavuori N110 Load Specifications (Use the Personalized Load Calculator below to adjust ) Bullet: .284 | 140gr | Berger VLD Hunting Manufacturer SKU: 28503 Bullet Weight: 140gr | 9.1g Bullet Diameter: 0.284" | 7.21mm Bullet Length: 1.267" | 32.2mm Caliber: 7 x 49 GJW load data Case Length (l3): 1.925" | 48.9mm Cartridge Length (C.O.L.): 2.842" | 72.2mm Seated Depth: 0.350" | 8.9mm Shank Seated Depth: 0.122" | 3.1mm Case Capacity: 36.5 Grains of Water | 2.37 cm³ Primer Size: Large Pistol (LP) Max. allowed Pressure: 63817 psi | 4400 bar LID: LID_B1027_C1083 Last updated: 2025-01-01 Recommended Twist Rate: 1:9 - 1:8 Load data for 0 loads in caliber 7 x 49 GJW with .284 | 140gr | Berger VLD Hunting bullet and 0 powders such as Accurate 4100, Hodgdon LilGun, SNPE Vectan BA6 1/2, Vihtavuori N110. The key underlying parameters are shown in the table above. Disclaimer Important Notice : DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service . Questions regarding the load data : Please read the information in the next tab "Explanations". Explanations | FAQs | Settings A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed" . Our load data might deviate from other sources - see the "most common reasons for deviations" . All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions " if you deviate. You can set your specifications in the "Personalized Load Calculator ". Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric) Barrel Length vs. Muzzle Velocity No data yet Personalized Load Calculator C.O.L. (Inch) C.O.L. (mm) We recommend you limit powder range to relevant brands to speed up re-calculation of results Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section . Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables. Case Length (Inch) Case Length (mm) CaseCapacity (GoW) Min z (%) Min FR (%) Max FR* Barrel Length (Inch) Barrel Length (cm) Safety Buffer (%) . Find Loads Sort by Filter by Powder Brand Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there. Powder Charge FR MaxP % V(0) z Max Load - Barrel Length: 5.50'' Powder Charge FR MaxP % V(0) z Start Load - Barrel Length: 5.50'' Any powder missing? Then click here . FR ... fill rate of the cartridge in percent MaxP ... max. pressure of load in psi or bar % ... max. pressure of load in percent of the maximum allowed pressure for this caliber V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s) z ... powder burnt in percent [...] * ... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads. [...] ² ... fill rate low - you might want to consider using a filler to ensure proper ignition. [...] ᴾ ... possible press load - work up slowly to this load while watching for signs of excessive pressure. 👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance. <>... you need to buy an access license to unlock the data